Clutch Hydraulic Line Bleeding
on the Mitsubishi 3000GT/Dodge Stealth

by Jeff Lucius


Any time that air has entered the clutch hydraulic lines, or if the fluid is dirty or has absorbed water, the lines must be bled. This operation both removes air bubbles in the line and flushes out the old fluid. Use a new, unopened container of brake fluid with a DOT 3 or DOT 4 rating. Brake fluid is hydrophilic, meaning that it will readily absorb water from the air or by direct exposure. For the $1.50 it costs for a 12-oz container, it is not worth using fluid from an opened container (except in emergencies). This process also goes much easier with two people.

The tools needed for bleeding the clutch hydraulic lines are the common ones that should be found in your in-car tool bag: screwdrivers; 10-mm and 12-mm sockets with extensions and wrench; and pliers. You will also need a 3/16" ID clear flexible hose about 12" long, a small plastic container about the size of a 1-lb margarine tub, and a fresh container of DOT3 or DOT4 brake fluid (6 oz is more than enough, about $1.50 for 12-oz at your local grocery or car parts store). All pictures are located near the end of this article.


These steps worked for me and my modified MAS/air filter setup. You may have to make some small change for your particular intake setup. You will need to remove the battery so make sure you have any security codes that may be required for devices such as the radio. Step 1 here may be the only essential one, depending on how limber you are.

1. Battery, tray, and washer tank. Disconnect the negative battery terminal first (always!). Then disconnect the positive terminal. Both are 10-mm nuts on the stock connectors. Remove the hold-down bar (10-mm nuts again). Lift the battery out of the car. Remove the four 12-mm bolts near the corners of the tray. Disconnect the washer electrical connector and fluid hose near the passenger's-side strut tower. See the pictures below. Lift the battery tray and washer tank out part way and disconnect the washer pump electrical connector (see picture). Remove the tray and washer tank from the car. Keep the washer fluid hose high to avoid spills. Clean your hands and tools if you suspect battery acid got on them.

2. MAS and air filter. Remove the intake air filter and the mass air sensor. This is a simple as just loosening one hose clamp for my ARC2 setup. It is a bit more complicated for the stock setup or K&N equipped cars.

3. Clutch vacuum pipe (AWD cars). Remove the metal pipe that runs across the corner of the battery and then down below the MAS. There are spring-type hose clamps at each end plus a bracket at the front end (12 mm bolt). In addition, a sliding clamp was attached to the battery hold-down bar.

4. Intake hoses. For turbo cars, remove the Y-pipe, the main intake hose that the MAS connects to, and the intake hose to the rear turbo (I leave the vacuum hose attached to the intake hose and disconnect it from the stock boost controller solenoid). I am not sure if the intake hose and resonator will be in the way for non-turbo cars. For the turbo cars, now is a great time to inspect the compressor wheel on the rear turbo, to check all the vacuum lines, to replace that stock BOV or check the seals on that aftermarket BOV. For all cars, the fuel filter is also easy to get to now, as well as the ISC motor on the throttle body.

Clutch hydraulic line bleeding

You may find it much easier to work around the release cylinder if you tie hoses and cables out of the way with some string. Be sure to clean your hands and tools if you get hydraulic fluid on them, the fluid may damage painted parts of your car or engine.

1. Clutch master cylinder. Locate the clutch master cylinder near the driver's side back corner of the engine bay (see picture below for AWD cars). Stuff disposable rags or paper towels around the cylinder and remove the lid (just pull up). Carefully pour some fluid into the cylinder. leave the top off.

2. Release cylinder. Locate the bleeder plug on top of the cylinder and carefully remove the cap. Place a small container (such as a 1-lb margarine plastic tub) on the cross member. Attach a clear 3/16" (4-5 mm) inside-diameter hose onto the bleeder plug. A piece about 12" long is plenty. Run the other end into the container.

3. Bleeding. Place your assistant inside and establish some clear instructions. The assistant will press the clutch pedal down and hold it down until you tell them to let up. With the clutch pedal up, loosen the bleeder nut with a 10-mm wrench. Tell your assistant to press down on the clutch pedal and hold it down. If no fluid comes out loosen the nut a little more. If no fluid still comes out, close (tighten) the nut and tell your assistant to raise the pedal. Loosen the nut again and press and hold the pedal. Repeat these steps till fluid starts to come out. The pedal may be harder to push down than normal because the vacuum assist is not functional if the vacuum pipe was removed (AWD only).

Once you get to fluid to come out, keep repeating the following steps until no dirty fluid comes and no air bubbles come out. Open nut and press down on clutch pedal. Close nut and release pedal. If the pedal is released with the nut open, air may go back into the lines. Checked the fluid level in the master cylinder after every 3 or 4 open/close cycles and add more fluid if necessary.

When you are satisfied, close the nut one last time, remove the bleeding hose, and put the cap back on. I used about 4 oz of fluid total when I replaced my clutch hose. Remove the bleeding hose and tub. Put the cap back onto the master cylinder and throw away the rags that were stuffed around it. If you get any brake fluid on the car paint, your hands, or tools, clean it off immediately.


Follow the preparation instructions in reverse and be sure to connect the negative battery terminal up last.

Service manual picture

Washer hose and electrical connector connected

Washer hose and electrical connector disconnected

washer pump

Clutch hose in car

Clutch bleeding 1

Clutch bleeding 2

Master cylinders

Back Home Forward

Except for the small gif and jpg images, the content, images, photographs, text, and multimedia displayed are Copyright ©2000-2002 by Jeff Lucius and Ken Wheeler. All rights reserved. No part, section, image, photo, article, or whole of this site may be reposted or redisplayed without permission of the authors.
Page last updated March 17, 2002.